For Sale: Custom front bumper-IA
#28
I'll see what I can do gotta wait till day light
Be a little more specific I could give alot of different measurements I won't beable to het you degrees of sweep or anything
I can tell you right now that It will fit in a 67x20x10 box
If you read the build thread Andy states the tube size which is 2x5 and 2x2 1/8" tubing which gives the middle section a height of 7" and that's all I an give you until daytime
Be a little more specific I could give alot of different measurements I won't beable to het you degrees of sweep or anything
I can tell you right now that It will fit in a 67x20x10 box
If you read the build thread Andy states the tube size which is 2x5 and 2x2 1/8" tubing which gives the middle section a height of 7" and that's all I an give you until daytime
#29
here is the measurements of the individual sections ill get more up and so som math and see if i can figure out the degrees of the angles and what not
heres some more measurements from the top so far ive figured the reward degree of sweep at 20.5°
ill try to get more later
Last edited by ambivolent; 04-01-2011 at 08:07 PM.
#35
Member
iTrader: (1)
Join Date: Mar 2011
Location: westminster,colorado
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
lol sweet bumper but i just going to make one cloes to this. enter the measurements on our 5x20 cutting table then weld it all up. more so for the mounts will be bolt on not weld in new mounts just becusae im geting a 3 inch body lift then have it painted in bedliner
#36
lol sweet bumper but i just going to make one cloes to this. enter the measurements on our 5x20 cutting table then weld it all up. more so for the mounts will be bolt on not weld in new mounts just becusae im geting a 3 inch body lift then have it painted in bedliner
#37
damn someone buy this! 400 to your door is a pretty good deal considering mosy of that is shipping. Dave get it!
the mounting isnt that bad. I cut off the frame horns(old bumper brackets) at a 45* and capped the ends. I then used some 1/2" angle iron on top of the frame on each side for the angle iron mounts on the bumper to slide on to. then its just bolted through the sides a couple times.
the mounting isnt that bad. I cut off the frame horns(old bumper brackets) at a 45* and capped the ends. I then used some 1/2" angle iron on top of the frame on each side for the angle iron mounts on the bumper to slide on to. then its just bolted through the sides a couple times.
#38
damn someone buy this! 400 to your door is a pretty good deal considering mosy of that is shipping. Dave get it!
the mounting isnt that bad. I cut off the frame horns(old bumper brackets) at a 45* and capped the ends. I then used some 1/2" angle iron on top of the frame on each side for the angle iron mounts on the bumper to slide on to. then its just bolted through the sides a couple times.
the mounting isnt that bad. I cut off the frame horns(old bumper brackets) at a 45* and capped the ends. I then used some 1/2" angle iron on top of the frame on each side for the angle iron mounts on the bumper to slide on to. then its just bolted through the sides a couple times.
I've had people say they'd buy it if I shipped and guess what I said yes and they back out a couple had legitimate reasons to back out not bashing on them but not sure about the others hell I've even put up specs for people wanting to build their own I plan on going off this bumper but gonna do an integrated winch and it would be easier to build it from scratch than it would be to modify this one
Before I bought this bumper took a picture of it into a local guy who quoted me $1100 and I had to leave my truck with him for a week this is a hell of a deal for something that isn't redadily available maybe I should start going up in price lol
Thread
Thread Starter
Forum
Replies
Last Post
Bigfoothunter_no1
OLD - Interior, Exterior, Electrical, & Misc.
0
04-11-2013 11:56 AM
For Sale: custom front bumper
bmandu
OLD - Interior, Exterior, Electrical, & Misc.
14
04-20-2010 02:26 PM