For Sale: explorer express eaton m90 xcharger kit with extras
#1
explorer express eaton m90 xcharger kit with extras
i am selling my very rare explorer express xcharger kit for the 5L v8 second gen explorers, or for the guys that have done a v8 swap in a RBV. this kit is i would say 95% complete. all that will be missing is 2 blots that hold 2 pulleys on (i have the part number, and you can get them from ebay or rockauto), a bracket that relocates the DEFP sensor to the firewall, and all the vacuum lines. other then that, it will come with all the hardware you will need, all the brackets you will need (and they are painted truefire blue, but are a little chipped up), 3 different pulleys (that make anywhere from 5lbs, to 10lbs of boost), 3 belts (one is new, never used), and even the instruction sheet. the extras that i will include are, 1 boost gauge, 1 Innovate LC1 Wideband (but i dont have the gauge), and 1 intercooler that has never been used, or mounted, and a intake elbow that i have made for it that you can put a 75mm throttle body on, but the stock one will also blot on to it..
i have had this kit on for aprox 2 years, and i am the second owner of it. it is a low mileage kit. the previous owner had told me that he only put about 20k miles on it, and i maybe have put 10k miles on it.
it works great. its has proven to be very reliable (i have drove down to philly with it on the truck twice, and it is a 27 hour drive one way) and have seen up to 19 mpg at 75mph (with proper tuning, and supporting mods). this kit can be bolted onto a stock motor with no tuning with the 3 inch pulley (5-6lbs of boost).
the only reason i am selling it is because i have now put a eaton m112 on it, and would rather see someone else be able to use it instead of it be shelved.
i am asking $2300 (u.s dollar) for everything in the pictures (one bracket is not pictured, it is still on the truck, but it will come with the kit, same with coil bracket, its on the truck still, but will come with it) plus any paypal fees, and shipping fees from manitoba canada postal code r1a 0p3
i am not on here to often, however if you have any doubts about me, i am on explorer forum lots.
i have had this kit on for aprox 2 years, and i am the second owner of it. it is a low mileage kit. the previous owner had told me that he only put about 20k miles on it, and i maybe have put 10k miles on it.
it works great. its has proven to be very reliable (i have drove down to philly with it on the truck twice, and it is a 27 hour drive one way) and have seen up to 19 mpg at 75mph (with proper tuning, and supporting mods). this kit can be bolted onto a stock motor with no tuning with the 3 inch pulley (5-6lbs of boost).
the only reason i am selling it is because i have now put a eaton m112 on it, and would rather see someone else be able to use it instead of it be shelved.
i am asking $2300 (u.s dollar) for everything in the pictures (one bracket is not pictured, it is still on the truck, but it will come with the kit, same with coil bracket, its on the truck still, but will come with it) plus any paypal fees, and shipping fees from manitoba canada postal code r1a 0p3
i am not on here to often, however if you have any doubts about me, i am on explorer forum lots.
#3
they dont come up often, and when they do, they dont come up this complete, or with extra goodies.
#4
I completely agree. If I wasn't already blowing up my budget with this 347 and other things I'm doing to my truck right now, I'd be all over it. No doubt it'd be great timing considering the 347 is going in as we speak, but it just doesn't make sense financially.
Thread
Thread Starter
Forum
Replies
Last Post
zabeard
OLD - Interior, Exterior, Electrical, & Misc.
1
12-08-2009 11:33 AM
zabeard
OLD - Engine & Drivetrain
31
12-03-2009 07:08 PM
TheBearJeweler
OLD - Engine & Drivetrain
7
05-20-2009 02:11 PM
whippersnapper02
4.0L OHV & SOHC V6 Tech
19
10-25-2007 08:25 PM