Got my explorer overhead console.
#1
Got my explorer overhead console.
HI!... Well I got my EXPLORER overhead console. It was bought as a kit. It came with the mounting bracket, temp sensor and pigtails for the sensor and the console. Even came with the mounting screws. lol! The only problem it is light blue.
That got fixed quickly. I dismantled the console and put it in my sandblasting cabinet on low PSI. About 40PSI. Worked perfectly. I luv not having to sand. lol! Got it painted tonight as well with the same trim paint I used on my dual "A" pillar gauge pod. Just got to put it back together tomorrow and then install it when I have time. Here's a few pics :
HPIM0674.jpg?t=1231831063
HPIM0675.jpg?t=1231831072
HPIM0711.jpg?t=1231831103
HPIM0712.jpg?t=1231831124
That got fixed quickly. I dismantled the console and put it in my sandblasting cabinet on low PSI. About 40PSI. Worked perfectly. I luv not having to sand. lol! Got it painted tonight as well with the same trim paint I used on my dual "A" pillar gauge pod. Just got to put it back together tomorrow and then install it when I have time. Here's a few pics :
HPIM0674.jpg?t=1231831063
HPIM0675.jpg?t=1231831072
HPIM0711.jpg?t=1231831103
HPIM0712.jpg?t=1231831124
#2
HI!... Here's some updated pics :
HPIM0718.jpg?t=1231888048
HPIM0719.jpg?t=1231888053
HPIM0728.jpg?t=1231888068
HPIM0727.jpg?t=1231888080
HPIM0731.jpg?t=1231888090
HPIM0718.jpg?t=1231888048
HPIM0719.jpg?t=1231888053
HPIM0728.jpg?t=1231888068
HPIM0727.jpg?t=1231888080
HPIM0731.jpg?t=1231888090
#3
HI!... Well I just finished the mechanical aspect of the console install. I'm probably going to wait until the weekend to do the electrical. I think it turned out well. Hopefully tomorrow I'll be able to get my hands on a EXPLORER center console. A guy I know says he has a bunch of them at the junk yard he works at.
Here's a few pics :
HPIM0732.jpg?t=1231900181
HPIM0736.jpg?t=1231900210
HPIM0745.jpg?t=1231900216
HPIM0744.jpg?t=1231900234
Here's a few pics :
HPIM0732.jpg?t=1231900181
HPIM0736.jpg?t=1231900210
HPIM0745.jpg?t=1231900216
HPIM0744.jpg?t=1231900234
#7
HI!... It helps to have the tools. I got sick and tired of having to run all over to get stuff done. I currently have a MIG welder, plasma cutter, drill press sand blasting cabinet with air filtration unit, 40 gallon parts washer, hydraulic press, brake, two electric air compressors and one gas powered portable (for the dragstrip), and more hand tools than I can count.
#8
Its not an actual button, you put the actual remote in that little compartment and when you push the 'button' it pushes the button on the remote. I can grab a pic of mine tomorrow.
Thread
Thread Starter
Forum
Replies
Last Post
ranger4.0
OLD - Interior, Exterior, Electrical, & Misc.
10
02-15-2011 11:25 PM
rangererv
OLD - Interior, Exterior, Electrical, & Misc.
1
08-27-2009 11:15 AM
TheBearJeweler
OLD - Interior, Exterior, Electrical, & Misc.
19
06-12-2009 07:26 PM
THE H.P FREAK
Interior Semi-Tech
4
02-15-2009 09:29 AM