ummm...mine are LED too...



I guess this means I need to go ahead and put the 4th and 5th ones in.

 

Hah dang, didnt notice that - I though tthey were incandescant ones!

Did you order the ones off Ebay - LED 15" bar with the high/low that you can tap into the brakes? :-)


Edit:

Hah was just laughing about the black truck in the pictures - it swaps position every new set of pictures :-p Thats my '88 Ranger I just got running again - 2.3L, 2wd. 5 speed (4+overdrive)... great condition minus the paint on the exterior - dove under it to do some inspecting and theres not even any rust on the frame minus the standard surface stuff from a little moisture here and there.. I missed drivin it :-)

 

Maybe back when we were doing your cluster, those may have been incandescants....but as soon as I went LED on the tails, everything went LED the same night(or the same week).

Link me these hi/lo clearence lamps...THAT would be hella awesome.

 

http://cgi.ebay.com/ebaymotors/15-Sl...Q5fAccessories


Dirt cheap - I'm going to be ordering up 2 more and tieing them into my left and right brake's... that way they will blink when I hit the brakes, and when I click my turn signals - still need to run wiring to my third brake light in the middle one so it will mimic the brake's without blinking on and off with a turn signal

 

hmmmm...found it. I kinda like it! Need to find red lense, then I may be set on it I suppose.

LED combination 3 light bar center brake light CLEAR:eBay Motors (item 290337646177 end time Aug-13-09 18:04:21 PDT)

EDIT: bam! http://cgi.ebay.com/ebaymotors/LED-c...Q5fAccessories

 

The one I linked to right there actually has a red, white, and black.. red = high, white = low, black = ground.. lets you tie into your brake light high/low so you can make it blink with that specific turn signal and such - My plan is to have 3 of these.. actually jsut ordered 2, and a can of nightshade - and going to paint the area under there black - nightshade the LED's so they wont blind so much when I hit the brakes.. and give them a stealthy look under there when they arent on.. one in the middle on the third brake light wires.. and one hugging each side workign with that ides brake light.

 

The link in your post sent me to his store home...

 

ohhh re-click that link, i edited it right after you c licked it I bet -- 15" Slimline 3 LED Red ID Light Bar Trailer Truck RV 80:eBay Motors (item 270318887154 end time Aug-13-09 1557 PDT)


If the link doesnt work.. search up "15" Slimline 3 LED Red ID Light Bar Trailer Truck RV 80" in the store =)

 

two wires: red and white, hot and ground. hehe...look at me..totally hacking your thread here.

 

lol thats a wrong picture on there.. its got three that was sent to me - low, high, and ground.. I think they are using a generic picture on that one probably, lol


Lol, and with thread hackign I dont mind at all - Im just waiting on those several HID haters to start spamming about me trying to kill people.. yadda yadda yadda lol :-p

 

Question about the HIDs you have... the duel beams. Do you have to hack the factory harness at all??

 

LED combination 3 light bar, high mount brake light red:eBay Motors (item 370239819339 end time Aug-10-09 1557 PDT)

Thats sweet, twist on the line of fire.

 

Should just be plug and play.

 

gotcha i was wonderin cause i have singles and was thinkin of upgrading.

 

This is how a proper HID kit works (With a relay)



Battery to Relay
Relay to Ballast
Stock Wiring plugs Into Relay (For High/Low Signals)
Ballast plugs into HID Bulb


Thats all there is to it - minus of course.. you have to mount the ballast and all that, slightly more work depending on application.

 

Does the hi/low kit have 2 relays since theres actually 2 bulbs? I've never seen the hi/lo relay kit.